Im building my wife a PC and now that my SLI is useless (for a few years now), I figured I’d give her my extra GPU.
I disabled the SLI in the control panel, powered down, popped the SLI and 2nd GPU out and gave my wifes pc the extra 1080. My PC started up fine, I booted up a game, and about 10 min in, the screen froze for about 10 seconds and then appeared to restart and now I have no video output. Did I brick my gpu? Any ideas on how to proceed?
I’m only panicking a lot.
Not sure since SLI is so niche I had to look up to remember what it is, but basic things to dummy check:
-are the various cables connected properly/card seated properly
-have you put the gifted wife-GPU into your system to test to see if that works on its own
-Is the GPU getting the proper power allotment since you reconnected things
-is your power supply failing
-Are there any past configurations you did to the failed card itself to enable SLI that its now expecting to see a second card and failing since its gone, beyond windows config.
-Is there something in the BIOS causing an issue
-is your MOBO failing
-have you given proper tribute to the local land god recently
if you have on board graphics with your cpu I’d connect your monitor to at least get into your BIOS and or Windows to poke around some more.
hard to really give any ideas not knowing the rest of your system but it’s also a possibility with a card that old that it might’ve just finally died. the 1080 is pushing a decade at this point.
Posting this on all threads:
Fixed: this was my first ever build and after reseating my gpu, I saw some less than intelligent wiring (6+2 pin coming out of my card, daisy chained to a 6 pin that then went into the VGA port on my power supply). I cringed and pulled those wires and replaced it with a PCIE cable from my wife’s new build (the reason I removed my 2nd 1080 in the first place). That cable only went into a CPU slot on the power supply but didn’t think much of it. Turns out using cables that are not associated with your specific PSU is a nono. Everything works fine and I am dumb for several reasons but at least I learned with (seemingly) no catastrophic consequences.
Thank yall for your help and consideration and sorry I wasted your time.
Do you not have an iGPU? The fact that it happened during gameplay makes me think that you have to zero out your drive and erase it. Not delete your OS but boot into a live USB program to actively write zeros across your drive and re-install OS.
To be sure, you could take out drive and plug into a different system to put from it and see if it works. So far I don’t suspect it’s a GPU issue but rather a driver or OS issue that only requires erasing your drive.
Posting this on all threads:
Fixed: this was my first ever build and after reseating my gpu, I saw some less than intelligent wiring (6+2 pin coming out of my card, daisy chained to a 6 pin that then went into the VGA port on my power supply). I cringed and pulled those wires and replaced it with a PCIE cable from my wife’s new build (the reason I removed my 2nd 1080 in the first place). That cable only went into a CPU slot on the power supply but didn’t think much of it. Turns out using cables that are not associated with your specific PSU is a nono. Everything works fine and I am dumb for several reasons but at least I learned with (seemingly) no catastrophic consequences.
Thank yall for your help and consideration and sorry I wasted your time.
I would still call this a personal success because how much you learned from this about cable management. I trust that from now on you will never take whatever random cables and p’ug them into whichever connection that looks. I hope also understand that it’s not always possible to diagnose a system issue without personally looking at it and trying to use it to see what is going on. For me, I would never think of asking the person if their video crd is daisychained but because is something normally never done. Each GPU gets their own cables plugged directly to the power supply
I vaguely remember ~7 years ago when I built it having issues with the gpus. The main issue was that I needed to boot my OS with a single card, get everything up and running, then shut down again and add the SLI and 2nd card. I also vaguely remember thinking the wiring was silly but it worked and for 7 years it was “if it ain’t broke don’t fix it” until now.
Update on my building journey: my wife’s new build (waiting for 3 more case fans):
I’d start by reseating the GPU. Bricking anything is unlikely. Unless you were generating a lot of static electricity and zapping the components.
Also, you plugged the GPU power in, right?
Posting this on all threads:
Fixed: this was my first ever build and after reseating my gpu, I saw some less than intelligent wiring (6+2 pin coming out of my card, daisy chained to a 6 pin that then went into the VGA port on my power supply). I cringed and pulled those wires and replaced it with a PCIE cable from my wife’s new build (the reason I removed my 2nd 1080 in the first place). That cable only went into a CPU slot on the power supply but didn’t think much of it. Turns out using cables that are not associated with your specific PSU is a nono. Everything works fine and I am dumb for several reasons but at least I learned with (seemingly) no catastrophic consequences.
Thank yall for your help and consideration and sorry I wasted your time.
Note: I’m sorta dumb with computers but smart enough to have built 3 that haven’t exploded yet (until now)
Repeating means pop it out and back in right?
Yes.
If you have a BIOS reset jumper, it might be worth setting that during the next boot too.
Tried that, got the monitor to wake up but still didn’t display anything. Then I replaced the power cable to the card and now the whole pc isn’t turning on so looks like I get to figure that out tomorrow. I’ll check if I have a jumper on my board too and get back to you. Thanks for the help though
ReSeating, not rePeating. But yes. It’s probably just GPU sag causing the card not sit properly in the slot. With the SLI bridge you had probably the weight of two GPUs weighting down the PCBs a little. Loosen the screws, push it in a bit (or pull it out fully and insert it again) and while tightening the screws make sure the card is a little aligned towards the top until they’re tight. Make sure your gpu power cable is properly seated too. If the card happens to still sag a lot you could also try to find something to lift it up, but make sure it is something that is a) not conductive and b) not gonna damage anything if it potentially falls over.
I know it sounds stupid…
But when you cut your GPU power almost in half… You turned settings down a lot right?
That would cause the crash, and sometimes a crash just kinda sticks, no fans, no lights, no output.
You have to flip the switch on the supply and do the hardest of reboots.
Like I said, you probably already did that stuff. But I’ve seen it happen.
The first thing you should always do is try turning it off and on again
Just to be safe do a clean install of the nvidia drivers. I’ve never personally ran SLI but who knows what might linger. Or if you really want to 110% it download DDU and the drivers. Reboot into safe mode (hold down shift when you click reboot, then pick the startup options), uninstall the driver, restart again (ideally with network disconnected) and install the nvidia drivers.
The only time DDU has fixed something a clean install didn’t was when I was really messing with some settings, but it doesn’t hurt to do it that way.
Posting this on all threads:
Fixed: this was my first ever build and after reseating my gpu, I saw some less than intelligent wiring (6+2 pin coming out of my card, daisy chained to a 6 pin that then went into the VGA port on my power supply). I cringed and pulled those wires and replaced it with a PCIE cable from my wife’s new build (the reason I removed my 2nd 1080 in the first place). That cable only went into a CPU slot on the power supply but didn’t think much of it. Turns out using cables that are not associated with your specific PSU is a nono. Everything works fine and I am dumb for several reasons but at least I learned with (seemingly) no catastrophic consequences.
Thank yall for your help and consideration and sorry I wasted your time.
Updating drivers was suggested by a friend to do after I started up but now I don’t have any video output so I guess I need to figure something else out . I feel dumb
Does your cpu have integrated graphics? If so you can plug video into the motherboard and update drivers from there.